新闻资讯

How To USE ANLERR Tiva Vaporizer Pen for dry herb

Release date: 2017-08-07 browsing: 0

ANLERR TIVA vaporizer pen is a self design,self produced pen shape no combustion dry herb vaporizer pen original from Anlerr. It is big vapor no combustion dry herb vaporizer pen with smooth airflow,full baked,pure taste. This model has been hot sell in vaporizer market now.Following are some tips for how to use ANLERR Tiva vaporizer pen.


Loading The ANLERR TIVA Vaporizer Pen for dry herb:

1)Caution: While using the TIVA,portions of the device may reach high temperature.Wait until the device has completely cooled before handling.

2)When loading the TIVA,remove the mouthpiece from the heating chamber lightly.

3)Apply your dry herbs into the heating chamber.Be sure not to over-pack the chamber or too tight as this can reduce airflow,effect the bake effective.

4)Once your products as been applied,re-attach the mouthpiece. 


Turn On/Off The ANLERR TIVA Vaporizer Pen for dry herb:

1)To turn on the Anlerr Tiva by pressing the power button 5 times in rapidly succession.

2)When turned on,the Anlerr Tiva will begin heating according to your last time use temperature.

3)You can control the temperature by press increase or decrease button and swift the temperature mode.

4)You can start to vape after reaching setting temperature).

6)After 5 minutes consecutively work,the Tiva will automatically shut down. This is the device’s safety power duration. To start your next session,simply repeat the process outline on this page.

7)To turn off the Tiva, press the power button 5 times in rapidly succession. The system will automatically shut down too when meet breakdown ((If there is any temperature adjust operation,the work time will calculate from the moment release the button.)

Temperature Control of the ANLERR TIVA Vaporizer Pen for dry herb:

1)The TIVA is capable of reaching any temperature within the ranged of 300-435℉/149-224℃.

2)By holding the power button for 3 seconds,you can alternate between Celsius and Fahrenheit temperature.

3)The TIVA comes equipped with a built in memory function,and will automatically heat to your last temperature selected when turned on.

4)USE the “+ “or “-” button,you can increase or decease the desired temperature when it is heating, 1℉ or 1℃ is a grade,the temperature adjust can be circulate (it will back to 300℉ when the temperature increased to 435℉and keep press “+” button;it will back to 435℉ when the temperature decreased to 300℉ and keep press “-” button).

5)Blue light will be blinking when it is heating,will be lighting all the time when reach setting temperature.


OLED Display of the ANLERR TIVA Vaporizer Pen for dry herb::

1)OLED display will show when work normally: Battery Power,Setting Temperature or heating temperature.

2)Battery Low: OLED Shows “LOW voltage”.

The red light will blink 10 times and show “LOW voltage” when device is nearly out of power in the working time,then turn off automatically to protect battery.

The red light will blink 5 times and show “LOW voltage” when it is heating,and then turn off automatically.

3)Temperature Heat Detector Malfunction:OLED shows “CHEEK NTC”

4)Heating Chamber Checking Malfunction:OLED shows “CHEEK FPC”.


Charging for ANLERR TIVA Vaporizer Pen for dry herb:

1)The charging current is 700mA,please use 5V 1000mA charger to charge.

2)A full charge is recommended before first use.

3)The blue light will blink when it is charging,will light all the time when full charged,voltage is 4.15V to 4.2V.

4)It will take approximately 1 to 1.5 hour to charge full.

5)The TIVA will stop heating when charging in its working time,and enter into charging situation to protect battery.

Specification of ANLERR TIVA Vaporizer Pen for dry herb:

1.Battery can work about 40 minutes consecutively  after full charge.

2.Temperature Range:300F-435℉(149-224℃)

3.Battery: 3.7V 16450 840mah Li battery.

4.Charger Standard: 5V/1000mah.

5.Max Work Current: 5A

6.Ceramic Heating Chamber Resistant and Max Out Watts:0.7ohm,23Watts.

7.System protection:over charging protection,short circuit protection.

8.Working Time: 5 minutes per circle.